Tascione

Hi, I sent this watch to a watchmaker ? last febuary, for a service it was returned to-day almost 3 months later. minus the second hand, i have a couple of second hands one of which may fit
Problem is i can,t get the movement out of the case, I have pulled the stem and removed the two case screws, but the Bezel wont move it very tight, any help , suggestions most welcome
Thanks Les

Side_2.JPG (62.27 KiB) Viewed 7867 times

Ok Les, Let's go through the steps. First remove both case screws. Next, There is a tiny little screw on the plate near the stem. Loosen that screw and remove the stem completely (Not just pull in out in the set position). Turn the dial face down in your hand and the movement should come right out. Give this a try and let me know. Good Luck, Ric

Hi Les,

Please forgive me but I'm going to ask the first really dumb question so far on the forum (I did mention that we should ask questions even if they seem dumb!) so here it goes...since the picture that I see is an edge on shot I can't really see the movement...but
Did you remove the bezel so that the movement can come out? It's still on the watch in the pic.

If I'm way off it was still fun asking!

Bob

if all else fails you could remove the crystal if its a plastic crystal (doubt full on a watch of that qaulity) it would be very easy. But this option is the only one i could think of if the movement is immovable.

Hi Bob, That’s what this forum is for, no offence taken, things that seem crazy but there must be a solution to them some place
I was a bit off the mark with my first post, now I have cooled down I shall try to explain, the watch in question
Is /was a 9ct gold 15j swiss watch running, I shall put photos on before & after, Now I have inspected the
Edge a dozen times and can not se any place for a knife to fit in to get the bezel off , when I say its tight I mean tight
I wish now I had tried to clean it myself, but being a valuable watch I fell for the cowboy repair man, any one with a solution
Very welcome to put there comments on

original face.JPG (67.83 KiB) Viewed 7841 times

original movement.JPG (67.96 KiB) Viewed 7841 times

returned face.JPG (73.32 KiB) Viewed 7841 times

Hi could not get the last photo its here , also note the damage at 5oc on the returned
watch, Ahh well thats life, Best regards Les

Hi Les,
I think that movement will drop out after you get that bezel off. Those pics help alot. I noticed some scratches along the edge of the bezel where others have tried to remove it in the past. As you probably are aware that's something you see far too often. You see it alot on screw back watches where people were not aware that it might have been a screw back. For that reason I almost always try unscrewing the back and the bezel just in case...unless there is an obvious lip designed into it for a knife to fit. Most try to pry (snap) the bezel off right around the pendant using the pendant to leverage the knife against as it appears others have tried on your watch in the past. Not really a good idea as damage can be done to the pendant. I always look around the edge with a loupe to find the place for the knife to fit. It's often that difficult to locate! Inserting the knife edge and pushing inward slightly is usually enought to "snap" it off. One thing that I suggest never doing (because I've done it more than once) is hitting the back of the knife with a small hammer. It does a pretty good job of popping off the bezel but the shock can easily break a balance pivot and or balance jewel on a non shock resistant watch...really...in fact it can even happen more than once if you're a slow learner...again really, live and learn I guess.
Anyway, might make sure the case screws are in place before popping that bezel off just in case that movt. wants to jump out of there!
Good Luck Les!

Bob

Hello, I managed to get the bezel off, for anyone with a similar problem this is how I did it, I got an industrial glove and a good strong pen knife, Held
The watch in the gloved hand put the knife in the bezel groove at 9oc and just increased pressure until
It popped, can now see the extent of damage, looks like it is now scrap gold