Hello everyone, stepping out with a recent clock overhaul. DO NOT QUOTE ANY OF THIS until its been properly corrected. thank you....First, I knew the clock would only run for a few seconds then stop, at the time I figured it was just dirty, I was just starting out. when I got to it I started to dismantle it and when I got to taking the dial off I broke a taper pin off trying to pull it out, then somehow I was able to break the other side of the same taper pin
![Embarrassed :oops:](./images/smilies/icon_redface.gif)
, with just enough to hold it on yet nothing to grab hold of. I could not punch it out for the life of me, so I filed it to the post and was able to remove the remaining pin later. made a tool that may work in the future for pushing taper pins out, any sugjestions on this issue????, besides not breaking it in the first place???? After taking about a hundred pics of how it should look when done I started to take apart, taking more pics as I went. this really helped for reassembly. I noticed slight grooves on the pallets of the escapement anchor.
![DSCN1950_01_01_01.JPG](./download/file.php?id=262&sid=0bdb378379b890a1985e564490e4396b)
- this is a deadbeat escapement with concentric locking faces adjustable in a slot on the anchor with a crutch and suspension invented by a german inventor named Henrich Kielmann patent #55006
- DSCN1950_01_01_01.JPG (26.96 KiB) Viewed 4499 times
. I read that these can be rotated if originally made correct, otherwise you can turn new ones. I used a diamond sharpening stone and lightly removed the grooves, I then finished the surface with a ceramic file. Supposedly the angle doesnt have to be exact but the locking should be 1/2 degree or a little more from the pivot of the anchor to the top of the escape wheel teeth, or is that the drop???. I also noticed that this has a adjustable anchor pivot, at least thats what I am thinking.
![DSCN1954_01_01_01.JPG](./download/file.php?id=264&sid=0bdb378379b890a1985e564490e4396b)
- DSCN1954_01_01_01.JPG (42.86 KiB) Viewed 4499 times
![DSCN1957_01_01_01.JPG](./download/file.php?id=265&sid=0bdb378379b890a1985e564490e4396b)
- this 1/2 moon knob looked to me like a adjustable anchor pivot ????
- DSCN1957_01_01_01.JPG (44.04 KiB) Viewed 4499 times
Moving on I cleaned all parts ultrasonically and used the timesavers old time solution, seems to work well but my experience is limited. I rebushed several pivot bushings by hand(I wanted to get a machine but figured if I do it by hand I will learn more about it), It was difficult at first but after practice and your videos I got the hang of it pretty quick. I recently purchased an old KWM bushing machine with all the reamers ect...works better than expected, I had already bought the bergeon bushing kit so I am going to get some bergeon reamers and outfit for both styles, I like the bergeon assortment but if I come across a KWM or American set that is cheap I will be able to use my machine for any kind, does this sound over the top????. I checked the mainsprings and one barrel had the pin bent and causing the barrel to push out at that point, I figured someone had wound it so tight that it caused this to happen, I did not see any cracks and decided to punch it back into shape, also the mainspring had the end of it tore off so I cut it and put a new locking hole in it to match what had been there, otherwise the springs and all looked good. THAT was my main cause of the clock not working
![Wink ;)](./images/smilies/icon_e_wink.gif)
. I checked all pivots and smoothed and burnished ones that needed it. putting it back together was a challenge for me, getting old, you know, 48 now, and vision is getting worse, and Bob as you know so is the memory, (used all my photos), I should be able to do this in my sleep by now as I have taken it apart about a dozen times, (great for learning)
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
. while assembling I had accidentally bent the flywheel pivot
![Shocked :shock:](./images/smilies/icon_eek.gif)
, I eventually found this out and straightened it out with smooth nose pliers. Can you use a punch with a hole in it for this?????? thought I heard that.
did some reading on pendulums and found a chart that shows clock trains with length of pendulum (Practical clock repairing by Donald de Carle). using the # of escape wheel teeth = 26 for this clock the pendulum should be 10.49 inches in length with 115.9 vibrations of pend. per minute.
![DSCN1955_01_01_01.JPG](./download/file.php?id=266&sid=0bdb378379b890a1985e564490e4396b)
- DSCN1955_01_01_01.JPG (32.87 KiB) Viewed 4499 times
I am thinking that since the pend. measures approx.16" from the suspension spring attachment then 2/3rds of the length would be the actual pendulum length from the crutch assembly, total. Using the thought of the center of oscillation. this makes sense to me for this clock but might not really mean anything. I noticed after all together that the forks on the crutch had to be snug but not tight to allow for the pend. to move perpendicular to the clockworks, also that the forks
must be at 90 degrees to the plates or else the pendulum will have a oval swing, do I see this right???? does the deadbeat require a pendulum impulse area as you show on your video??? Well, I now know what you meant when you said that the time train will frustrate people to the point of giving up, this has been my worst enemy. Never worked right and still intermittent issues. the only way I could get it to gong properly was having the knife fall onto the locking plate a little bit past the dropoff while it wound the hammer into the up position, otherwise it would gong the 1/2 hour too many times in a row..????? still frustrating to me but I will not let it win!!!!
![Laughing :lol:](./images/smilies/icon_lol.gif)
so far it is keeping good time and I look forward to any feedback.
William